A Brand new semi-automated frequency analyser design built around our super stable and highly successful load cell technology which has driven our line of reference analysers for the past 2 decades.
Key design features of this new development were driven for the most part by the shaft manufacturer's need for speed and reliability when testing shafts coming off the production line. We've also integrated several small refinements into the design demanded by advanced clubmakers heavily vested into shaft customization powered by proprietary shaft databases built around advanced shaft profiling systems (APS).

030125-BCP Barcode Printer Port upgrade available! Must be installed by Golfmechanix technicians in-house. Contact us for more detail.

This is the manual version of the APS Heavy Duty frequency analyzer
030125-HD. We’ve replaced the pneumatic cylinders with our torque
limited knobs so that clubmakers that do not have access to an air
compressor can still perform advanced shaft zone profiling analysis
using our new Frequency Auditor engine and the optional zoning beam.

Top of the range frequency analyzer measures shaft oscillations up to 1,000 CPM with 0.1 CPM accuracy. Easy-to-use interactive parameter setup, averaging function, cycle count mode, and more. Built-in analog and digital computer interface. Constant pressure 5 inch clamp with torque-limiting knob screw.

The Auditor Heavy Duty Optometrix Frequency Analyzer is an invaluable tool for high-volume clubmakers used to consistently measure shaft frequency of both assembled clubs and raw shafts. Other frequency machines measure by reflected light which often results in missed or inconsistent frequency readings. By using a laser as the primary light source, measurements are not affected by ambient or reflected light, shaft color or shaft material. A heavy duty base protects the electronic components of the analyzer.

An original idea we turned into reality that can potentially save a lot of time
and headaches for any clubmaker wanting to FLO shafts fitted with OEM
adapters! These two unique models fit over shaft adapters and bare shaft
tips using a large capacity collet that is hand tightened to securely fasten the
laser to the shaft with no backlash. Rings and battery included.

This standard model has a tough Nylon collet and
is as effective as the HD model. This is best suited
for the occasional clubmaker. The assembly weighs
205 grams. Rings and battery included

A Chucked Tip weight and FLO tracer featuring our new stackable weights
that simulate the load applied to the shaft when the head is installed. The
simulated weight can also provide trimmed shaft frequency prior to assembly which can be a major plus when building frequency matched clubs. The chucked tip weight can be mounted on shafts with a tip diameter not exceeding 13mm or.510". 205 grams base weight. Rings and battery included.

Finally, a perfectly balanced, 205 gram, frequency tip weight with a built-in laser and an internal long-life CR2 battery. This handy and easy-to-use tool works great for floing shafts before assembly. Mount the tip weight on the shaft and turn it on. Twang the shaft to start oscillations and observe the pattern. Rotate shaft to align the spine in the plane.

Encompassing all the calibration standards a club-maker needs to keep his instruments in top condition; We’ve designed this unique standard that provides base measurements for Mass, Frequency, 1st and 2nd Moment of inertia, length and
spring rate!

This frequency analyzer uses our latest hardware and firmware designed specfically for shaft profiling. This design has two split clamps to accommodate shafts with unusual butt geometry as well as gripped clubs. One additional advantage to the split clamp is a better pressure distribution and therefore a better coupling with the clamp less energy loss which can be easily picked up by the highly sensitive strain gauge sensor.

This frequency analyzer uses our latest hardware and firmware designed specfically for shaft profiling. This design has two split clamps to accommodate shafts with unusual butt geometry as well as gripped clubs. One additional advantage to the split clamp is a better pressure distribution and therefore a better coupling with the clamp less energy loss which can be easily picked up by the highly sensitive strain gauge sensor.

The use of Pneumatic clamp onthis inherently fast frequency analyzer improves speed and performance when working with gripped clubs. The clamping pressure and clamping speed are easily adjusted, allowing clubmakers with a hight work turn around a little bit more flexibility without hurting quality or productivity

Industry standard frequency tip weights, precision machined and balanced, placing the centre of gravity at the shaft tip vertical axis to eliminate the cantilever effect which can offset CPM readings by few points. The lighter 205 gram tip weight is machined from steel while the heavier weights ranging from 215 through 615 grams are machined from solid brass.

Please click on the option icon to order the weight of your choice

An essential tool in the toolbox of clubmakers interested in spine detection and orientation. Clips onto the butt of the shaft to give accurate 360 degree shaft positioning, in one-degree increments.

Universal Shaft Chuck is designed to be used as both a frequency analyzer weight and a shaft tip I.D. drill guide for unclogging epoxy when reshafting clubs. The 3.6 mm drill bit is included.